Chemical-free mold removal for wood, framing, and crawl spaces

Dry Ice Blasting Mold in CAPISTRANO BEACH, California

Dry Ice Blasting Mold in CAPISTRANO BEACH, California strips mold off framing, sheathing, and crawl space joists without water, sand, or harsh chemicals. If you have dry ice mold removal in CAPISTRANO BEACH California on your list, we handle the containment, the blasting, and the HEPA cleanup in one visit. Coastal humidity here feeds mold fast, so the sooner we blast it, the less material you replace.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Dry Ice Blasting Mold by Mold Remediation Service Capistrano Beach
Careful work. Honest options.
About this service

Dry Ice Blasting Mold in CAPISTRANO BEACH, California

Dry Ice Blasting Mold in CAPISTRANO BEACH, California is a media-blasting remediation method that fires soft dry ice pellets at roughly -109°F to lift mold, spores, and surface staining off building materials. The pellets hit the surface, flash-freeze the growth, and sublimate straight to gas on contact, so there is no sand, no water, and no secondary waste to shovel out. That matters on wood framing, plywood sheathing, and concrete where sandblasting would gouge the grain and chemical washes would soak the lumber.

We see the same pattern across Capistrano Beach: marine air pushes humidity into crawl spaces and attics, a slow roof leak or a supply line drip goes unnoticed, and black mold growth takes hold on the framing within a few weeks. Homeowners searching for affordable dry ice mold removal in CAPISTRANO BEACH California usually find us after a musty odor or a moisture meter reading they did not expect. We confirm the moisture source first, then blast.

  • ✓ No Water, No Secondary Waste
  • ✓ Reaches Tight Framing Cavities
  • ✓ Safe on Wood and Wiring
  • ✓ Kills Odors at the Source
What's included

What Our Dry Ice Blasting Mold Service Includes

Every dry ice blasting job includes the full scope from inspection through clearance testing. We do not piece it out. Here is what you get when you book us for Dry Ice Blasting Mold in CAPISTRANO BEACH, California.

✓

Full Moisture Inspection

We map the affected area with a thermal imaging camera and moisture meter, and check inside wall cavities with a boroscope inspection camera. This tells us exactly what needs blasting and what needs replacing.

✓

Containment and Negative Air

We build a 6-mil plastic containment with zipper doors and run a negative air machine with HEPA filters. This keeps spores from spreading to the rest of your home during the blasting work.

✓

Dry Ice Blasting of Affected Surfaces

Our technicians blast the mold off framing, sheathing, and other structural surfaces using a dry ice blasting machine. No water, no sand, no chemical residue left behind.

✓

HEPA Vacuum and Antimicrobial Coating

After blasting, we HEPA vacuum every surface inside the containment and apply an antimicrobial coating to the cleaned framing. We use products like Concrobium and Fiberlock where the substrate calls for it.

✓

Post-Remediation Air Sampling

We collect air samples with an air sampling pump and send them to an accredited lab. Results come back in 24 to 48 hours, and you get the written report for your records or insurance claim.

✓

Debris Disposal and Site Cleanup

Any removed material is bagged, sealed, and disposed of per California Department of Public Health guidelines. We leave the site clean and ready for reconstruction if any is needed.

How it works

How Our Dry Ice Blasting Process Works

01

Inspection and Moisture Mapping

We start with a thermal imaging camera and a moisture meter to map where the water is coming from and how far the mold has spread. A boroscope inspection camera goes into wall cavities and joist bays. This takes 45 to 90 minutes on a typical Capistrano Beach home, and it tells us exactly what needs blasting and what needs replacing.

02

Containment Setup

We build a containment barrier with 6-mil plastic sheeting and zipper doors to keep spores out of the rest of your house. A negative air machine with HEPA filters pulls air through the containment and exhausts it outside. This step takes about an hour and is what keeps the rest of your home clean during the job.

03

Dry Ice Blasting

Our technicians suit up in disposable coveralls and respirator cartridges, then run the dry ice blasting machine across the affected framing. Pellets hit at roughly -109°F and lift the mold off the surface. A typical crawl space takes three to five hours; a full attic can run a full day. We check progress with the moisture meter as we go.

04

HEPA Vacuum and Antimicrobial Treatment

Once the blasting is done, we HEPA vacuum every surface inside the containment to capture loose spores. Then we apply an antimicrobial coating to the cleaned framing. We use products like Concrobium and Fiberlock where the substrate calls for it. This step takes two to three hours and is what stops regrowth.

05

Post-Remediation Verification

We run an air sampling pump to collect spore counts inside and outside the containment, then send the samples to a lab. Results come back in 24 to 48 hours. If counts are not where they need to be, we re-blast at no additional charge. You get the lab report in writing for your records or your insurance claim.

Tools & methods

Tools and Methods We Use

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Dry ice blasting machine

Fires dry ice pellets at roughly -109°F to lift mold off framing, sheathing, and concrete without water or abrasives.

Thermal imaging camera

Finds hidden moisture behind walls and in ceilings before we open anything up. It shows us where the water is, not just where the mold is.

Moisture meter

Confirms moisture content in wood and drywall before, during, and after blasting. We use it to verify the substrate is dry enough to treat.

Boroscope inspection camera

Looks inside wall cavities and joist bays through small openings so we can scope the job without tearing out more material than necessary.

Negative air machine with HEPA filters

Pulls air through the containment and exhausts it outside, keeping spores from spreading to the rest of the house during blasting.

Air sampling pump

Collects air samples before and after remediation so we can verify spore counts with a lab report.

Dehumidifier and air scrubber

Brings humidity down after blasting and scrubs the air inside the containment. We use Dri-Eaz and Phoenix Restoration units on most jobs.

Real results

Before and after.

Crawl Space Mold After Supply Line Leak

Before

A slow supply line leak under a Capistrano Beach home soaked the crawl space for weeks before the homeowner noticed a musty odor. Joists and subfloor showed heavy black mold growth across roughly 300 square feet.

After

We contained the crawl space, blasted the joists and subfloor in about four hours, HEPA vacuumed, and applied an antimicrobial coating. Post-remediation air sampling came back clear, and the musty odor was gone within 24 hours.

Attic Truss Mold From Roof Leak

Before

A roof leak above a Doheny Village home dripped onto the attic trusses for two seasons. Visible mold covered about 200 square feet of trusses and sheathing, and the homeowner was worried the wood would need to be replaced.

After

We repaired the leak source, contained the attic, and blasted the trusses and sheathing with dry ice. The wood came out clean without gouging, and lab results confirmed spore counts were back to outdoor baseline levels.

Bathroom Ceiling Mold in Beach Cottage

Before

A beach cottage near Beach Road had recurring bathroom ceiling mold that came back every few months despite repeated bleach treatments. The exhaust fan was moving less than 30 CFM, well below what the room needed.

After

We blasted the ceiling and exposed framing, applied an antimicrobial coating, and replaced the exhaust fan with a 110 CFM unit. The mold has not returned, and the homeowner stopped buying bleach.

Problems we solve

Mold Problems We Solve in Capistrano Beach

Coastal humidity and older building stock create specific mold problems in Capistrano Beach. Here are the ones we handle most often with dry ice blasting.

Ask a pro →
01

Crawl space mold on joists and subfloor

We contain the crawl space, blast the joists and subfloor with dry ice, then run a dehumidifier to bring humidity down. Most crawl spaces are clean in a single day, and we verify with post-remediation air sampling.

↗
02

Attic mold from roof leaks and poor ventilation

We locate the leak source, contain the attic, and blast the trusses and sheathing. For HVAC mold contamination, we blast the affected ductwork surfaces and follow with a fogger treatment where needed.

↗
03

Bathroom ceiling mold from steam and poor exhaust

We blast the ceiling and any exposed framing, treat with an antimicrobial coating, and check the exhaust fan CFM to make sure it is actually moving air. If the drywall is compromised, we remove and replace it.

↗
04

Black mold growth after a slow supply line leak

We use a thermal imaging camera to find the wet zone, open the wall, and blast the framing. Insulation is removed and replaced. We document everything with photos and moisture readings for your insurance claim.

↗
Proof you can check

Licensed, Certified, and Verified

✓
IICRC AMRT (Applied Microbial Remediation Technician)Institute of Inspection, Cleaning and Restoration Certification
✓
IICRC WRT (Water Restoration Technician)Institute of Inspection, Cleaning and Restoration Certification
✓
ACAC CMI (Certified Microbial Investigator)American Council for Accredited Certification
✓
EPA Lead-Safe Certified FirmU.S. Environmental Protection Agency
✓
California CSLB Licensed ContractorCalifornia Contractors State License Board
Good questions

Frequently Asked Questions About Dry Ice Blasting Mold

(833) 929-5837 →

Most residential dry ice blasting jobs in Capistrano Beach run $1,800 to $6,500 in 2026, depending on square footage and how far the mold has spread. A small crawl space can come in under $2,000, while a full attic with HVAC contamination can push past $6,000. We give you a written price after the inspection, before any work starts.

Yes. Dry ice blasting is non-abrasive, so it cleans wood framing, plywood sheathing, and dimensional lumber without gouging the grain or driving moisture into the wood. We dial the pressure to match the substrate and verify with a moisture meter as we go. It is one of the safest methods for structural wood that you want to keep.

Dry ice pellets are accelerated through a blasting nozzle at roughly -109°F. When they hit the mold, the thermal shock freezes and lifts the growth off the surface, and the pellets sublimate into CO2 gas on contact. There is no water, no sand, and no secondary waste. We follow with a HEPA vacuum and an antimicrobial coating.

We do. Our crew is based locally and handles cryogenic mold removal CAPISTRANO BEACH 24/7, including same-day emergency calls. We are IICRC AMRT certified, EPA Lead-Safe Certified, and licensed through the California CSLB. Call (833) 929-5837 and we will schedule an inspection, usually within 24 hours.

Ready when you are

Get Dry Ice Blasting Mold in CAPISTRANO BEACH, California

We are licensed, insured, and IICRC certified, and we answer the phone 24/7. Call now and we will schedule an inspection, usually within 24 hours, and give you a written price before any work starts.

Schedule Inspection (833) 929-5837 →
Request an appointment

Contact Our Mold Remediation Team

Call (833) 929-5837 or send us a message and we will get back to you the same day. We answer 24/7 for emergency calls and schedule inspections Monday through Friday. If you have photos of the mold or a moisture issue, send them over - it helps us give you a faster, more accurate scope.

Request received — our team will be in touch shortly.
Tap to call(833) 929-5837